TWL6032A2B6YFFR Power Path Management IC PMIC Fully Intg PWR Mgmt

1 Features

• Five Highly Efficient Buck Converters

  • – One 3 MHz, 0.6 to 2.1 V at 5.0 A, DVS-Capable

  • – One 6 MHz, 0.6 to 2.1 V at 2.5 A, DVS-Capable

  • – Three6MHz,0.6to2.1Vat1.1A,OneIsDVS-

    Capable

  • – Extended Mode for Higher Output Voltages

• 11 General-Purpose Low-Dropout Voltage Regulators (LDOs)

– Six1.0to3.3Vat0.2AWithBatteryor

Preregulated Supply:

• One Can be Used as Vibrator Driver

• One1.0to3.3Vat50mAWithBatteryor

  Preregulated Supply

• One Low-Noise 1.0 to 3.3 V at 50 mA With

  Battery or Preregulated Supply

• One3.3Vat100mAUSBLDO

• Two LDOs for TWL6032 Internal Use

• USB OTG Module:

  • – ID Detection, Accessory Charger Adapter (ACA)

    Support

  • – Accessory Detection Protocol (ADP) Support

• Backup Battery Charger

• 12-Bit Sigma-Delta Analog-to-Digital Converter

  (ADC) With 19 Input Channels:

  – Seven External Input Channels

• 13-Bit Coulomb Counter With Four Programmable

  Integration Periods

• Low-Power Consumption:

  • – 8 μA in BACKUP State

  • – 20 μA in WAIT-ON State

  • – 110 μA in SLEEP State, With Two DC-DC

    Converters Active

• Real-Time Clock (RTC) With Timer and Alarm

  Wake-Up:

  – Three Buffered 32-kHz Outputs

• SIM and SD/MMC Card Detections

• Two Digital PWM Outputs

• Thermal Monitoring:

  – High-Temperature Warning – Thermal Shutdown

• Control:

• – Configurable Power-Up and Power-Down

  Sequences (OTP Memory)

• – Configurable Sequences Between SLEEP and

  ACTIVE States (OTP Memory)

• – Three Digital Output Signals that can be

  Included in the Startup Sequence to Control

  External Devices

• – Two Inter-Integrated Circuit (I2C) Interfaces

• – All Resources Configurable by I2C

  • System Voltage Regulator and Battery Charger With Power Path From USB:

• – Input Current Limit to Comply With USB

  Standard

• – 3-MHz Switched-Mode Regulator With

  Integrated Power FET for up to 2.0-A Current

• – Dedicated Control Loop for Battery Current and

  Voltage

• – External Low-Ohmic FET for Power Path and

  Battery Charging

• – Boost Mode Operation for USB OTG

• – Supplement Mode to Deliver Current From

  Battery During Power Path Operation

• – Charger for Single-Cell Li-Ion and Li-Polymer

  Battery Packs

• – Safety Timer and Reset Control

• – Thermal Protection

• – Input/Output Overvoltage Protection

• – Charging Indicator LED Driver

• – Compliant With:

  • USB 2.0

  • OTG and EH 2.0

  • USB Battery Charging 1.2

  • YD/T 1591-2006

  • Japanese Battery Charging Guidelines

    (JEITA)
    • Battery Voltage Range From 2.5 to 5.5 V
    • Package 5.21-mm × 5.36-mm 155-Pin WCSP

The TWL6032 device is an integrated power-management integrated circuit (PMIC) for applications powered by a rechargeable battery. The device provides five configurable step-down converters with a current capability of up to 5.0 A for memory, processor core, I/O, auxiliary, preregulation for LDOs, and so forth. The device also contains nine LDO regulators for external use that can be supplied from a battery or a preregulated supply. The power-up and power-down controller is configurable and can support any power-up or power-down sequence (programmed in OTP memory). The RTC provides three 32-kHz clock outputs: seconds, minutes, hours, day, month, and year information; as well as alarm wakeup and timer. The TWL6032 device supports 32-kHz clock generation based on a crystal oscillator.

The device integrates a switched-mode system supply regulator from a USB connector. The switched- mode regulator includes power paths from the USB and battery with supplemental mode for immediate startup, even with an empty battery. The battery switch uses an external low-ohmic PMOS transistor allowing minimal serial resistance during fast charging and when operating from battery. The device can also be used without the external PMOS transistor; in this case, the battery is always tied to the system supply and the switched-mode regulator is used for battery charging.

The TWL6032 device is available in a 155-pin WCSP package, 5.21 mm × 5.36 mm with a 0.4-mm ball pitch.